Parts & Accessories

- Self-adhesive, weaved polyester premium quality rim tape. About 3g per wheel instead of 30g for a regular rubber rim tape - Sold by the roll, 1 roll will do about 20 wheels

- Soft and elastic for an easy mounting - Resistance to high pressure: 8 bar / 116 psi - High resistance to punctures - Sold by the unit

- Soft and elastic for an easy mounting - Resistance to high pressure: 8 bar / 116 psi - High resistance to punctures - Sold by the unit

- Soft and elastic for an easy mounting - Resistance to high pressure: 8 bar / 116 psi - High resistance to punctures - Sold by the unit

Schwalbe High Pressure Rim Tape effectively protects the tube against mechanical damage. - Elastic for ease of installation - High pressure: 8 bar / 116 psi

Stan's No Tubes' Presta Removable Valve Core is a replacement valve core for Stan's No Tubes Presta valve stems and Presta valve equipped rim strips.

Sold by the unit

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

- High performance adhesive tape, a great pairing with Velox Cement - Each roll is usually adequate for gluing two tubular tires - Protects tube from spoke/nipple/rim puncture

Pack of 30 ornaments. - 5 different colors - Fits all standard spoke diameters

Front axle conversion kits convert your hub to fit a new axle measurement or for a new group set. - DT 350 20x110mm Left Dust Cap

Replacement Pawls for all Oozy hubs.

This lightweight, high-pressure rim tape offers great protection against spoke hole flats and is easy to install. This Italian-made tape is light and thin, so it will not inhibit tire fitting. Nylon elastic material is used to ensure a snug fit without movement.

Small component with a large impact. A poorly constructed or unsuitable tyre rim tape can be the cause of many punctures. It is especially important with hollow section rims to use a pressure-resistant rim band which covers the entire rim. The fabric-reinforced Continental Easy Tape rim protector is designed for use under high air pressure conditions. The various widths enable a perfect fit for all standard rims. The high pressure design for racing cyclists withstands up to 220 psi, without becoming deformed. The flat construction type also significantly eases the job of tyre fitting.

Front axle conversion kits convert your hub to fit a new axle measurement or for a new group set.

Looking for a super lightweight but badass tubeless sealant? Boom, you've just found it my friend! No Puncture Hassle performs under the most brutal race conditions. The cutting-edge microfiber molecules fill the bigger holes and tears, whilst the advanced latex forms a strong seal instantly. The formula also contains a unique UV detection system that highlights any punctures you haven’t seen during your ride. Developed with the world's top downhillers and pro peloton teams, to give you the finest tire sealant available. It's non-corrosive and easily washes off with water. Compatible with tubeless ready and full UST wheels/tires, No Puncture Hassle works from 15psi-120psi and temperatures from -20°C to +50°C. Our pouch is designed to fit your Presta valve perfectly and is ideal to add to your toolkit or ride pack for emergency top ups on the go! - For Downhill, Enduro and Road tires - Seals tears and holes up to 6mm - Contains UV puncture detection - Won't dry out or ball - Works from 15psi-120psi and temperatures from -20°C to +50°C - Biodegradable

On today's MTB frames, there are many dropout diameter and width standards. Most Mavic wheels can be fitted with specific adapters to match your wheelset with your frame. - Converts Crossmax rear wheels from 135mm to 142mm spacing - One pair required for each hub to be converted

- Extra long quick release for rear axle mount rack systems

Replacement bearings and bushings specific to Spoon 90 (Small) and 100/110 (Medium and Large) pedals. Eliminates play that can develop over time, and revives performance. Includes: - Sealed Bearing x2pcs - 10mm IGUS Bushing x2pcs - Green Friction Seal x2pcs - Locknut - O-ring x 2pcs

Replaceable hub guard for the Odyssey Vandero Pro and GSport Roloway front hubs. Made from a special proprietary plastic blend for increased durability. Sold individually. Features: - Proprietary Plastic - Press Fit

Package comes with two pieces of rim tape for use with the Zipp clinchers. Woven nylon material. Tape is extra thin with a thickness of 0.5 mm. Note: For Zipp 700c and 650c aluminum/carbon hybrid clichers, use the 16 mm rim tape. For Zipp 30 wheel set use 18mm but for the wider Firecrest and Firestrike carbon clinchers use the 20mm x 1/2mm rim tape.

Zipp Speed Weaponry Valve Extender Wrench Set - Two 4 mm and 5 mm combination wrenches - Replacement wrenches required to properly install Zipp integrated valve extenders - Use with Zipp Tangente tubes with aluminum Presta valve and aluminum valve extender

Tubeless valves for DT Swiss rims for repair or replacement. - DT Swiss Narrow Base Tubeless Valve - 40mm

- 3-piece kit to secure wheels and seatpost - Lighter and safer than regular QR skewers - MTB 100mm/135mm - Seatpost: M6 x 45mm

Aluminum Tubeless Presta Valve - MTB or Road

Aluminum Tubeless Presta Valve - MTB or Road - 18-25mm for Asymmetric Rims

Aluminum Tubeless Presta Valve - MTB or Road - 18-25mm for Cylindrical Rims

Tubeless valves for DT Swiss rims for repair or replacement. - DT Swiss Narrow Base Tubeless Valve - 53mm

Tubeless valves for DT Swiss rims for repair or replacement. - DT Swiss Narrow Base Tubeless Valve - 63mm

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

14-gauge spoke nipples made from high-grade aluminum and less than half the weight of traditional brass nipples. Available in an assortment of anodized colors. Product Specifications - Material: Aluminum - Gauge: 14g - Length: 16mm (5/8") - Quantity: 40pc per pack - Weight: 0.7oz per pack

The Muc-Off Tubeless Rim tape is made from their proprietary performance material with a pressure-sensitive adhesive to provide just the right amount stretch whilst maintaining durability and strength needed to create a lasting airtight seal. Semi-transparent material makes locating the valve hole easy.

WTP's Helix hub guards are designed to work on The Helixline of hubs, replacing the cones for a perfect fit without having to spread your dropouts. - Includes heat-treated chromoly adaptor to replace hub cone nuts for a perfect fit - Rear Hub guards are compatible with Helix V1 and Helix V2 freecoaster hubs and many other "KHE" style freecoasters on the market

Are the bearings on your WTP Helix rear hub getting a little crunchy? Yeah, that happens when you're punishing your bike with progressing all the while. Fear not, we've got you covered with this high-quality replacement bearing set from WeThePeople. - Seal color may vary, but the high quality stays the same

Tubeless valves for DT Swiss rims for repair or replacement. - DT Swiss Narrow Base Tubeless Valve - 73mm

Replacement Steel Axle Shaft for Spike Boost R148 and Oozy Boost R148 Rear hubs.

Replacement Steel Axle Shaft for SPIKE DH R150 Rear Hubs. Compatible with 12x150mm hubs and those already converted to 12x157mm. - Material : Steel - Weight (g): ±81 - Compatibility: SPIKE DH 12x150mm / 12x157mm (converted) Rear Hubs

SPANK SPOON Hub Single Speed Conversion Kit. - Cassette spacers - 13T driver cog - Cassette lock ring

The CF front hub guard presses directly over existing Cinema hub hardware to protect your hub and spokes on grinds. Injection molded from super durable nylon material, this guard can handle some serious abuse while still being affordable. - Material: Nylon - Fits: Cinema FX, VX2 and ZX Front Hubs and Wheels (2017 and later) - Side: Either Side - Weight: 0.9 oz

Designed for the non-drive side, the CR rear hub guard presses directly over existing hub hardware to protect your hub and spokes. Injection molded from super durable nylon material, this guard can handle some serious abuse while still being affordable. - Material: Nylon - Fits: Cinema FX & FX2 Freecoaster; VX2, VX3, and ZX Cassette Hubs and Wheels (2017 and later) - Side: Non-Drive Side - Weight: 1.3 oz

Designed for drive-side use only, the DR rear hub guard presses directly over existing Cinema hub hardware to protect your chain, driver, and hub shell on grinds. Injection molded from super durable nylon material, this guard can handle some serious abuse while still being affordable and easily replaceable. - Material: Nylon - Fits: Cinema FX & FX2 Freecoaster; VX2, VX3, and ZX Cassette Hubs and Wheels (2017 and later) - Side: Drive Side - Weight: 1.1 oz

The Cinema VF (uniVersal Front) hub guard is injection molded from an ultra-durable and fast sliding nylon composite. Designed to work with as many different front hub and fork combinations as possible, the VF guard covers either side of your hub and fork dropouts to protect them during grinds. Simply install outside the fork dropout, without replacing any hub hardware and without spacing out your forks. - Material: Nylon - Fits: Most Front Hubs - Weight: 0.9 oz

The Cinema VR (uniVersal Rear) hub guard is injection molded from an ultra-durable and fast sliding nylon composite. Designed to work with as many different rear hub and frame combinations as possible, the VR guard covers the drive side or non-drive side of your rear hub and protects it from grinds. Simply install outside the frame dropout without replacing any hub hardware and without needing to space out your frame. - Material: Nylon - Fits: Most Rear Hubs - Weight: 1.2 oz

SRAM's X0 conversion caps are the ticket for converting your X0 hubs to a different axle type.

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

Developed for short spokes with a large deflection angle. DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use. - Weight: starting at 59g for 64 nipples.

A pair of lightweight, 17mm aluminum axle nuts. - 14mm fits most rear axles (M14xP1.0) - 3/8" fits most front axles (3/8x26T) - 7075-T6 aluminum - Weight: 0.8oz

A pair of steel axle nuts. - 17mm wrench flats

The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples

A modern take on the classic internal/enclosed cam design as invented by the late, great Tullio Campagnolo. - Internal cam design exerts a far greater vise-like grip vs. external/exposed cam QR lever designs for a more secure fit - Fits both road and mountain bike frames & forks with 100/130/135mm hub spacing - Construction: Chromoly steel skewer with alloy lever and plastic/steel body & acorn-nut - Sold as a front & rear matching pair - Lengths: 133mm (FR) / 169mm (RR) - Weight: 57g (FR) / 61g (RR)

Designed to protect your hub and spokes on grinds! The Mission front hub guard fits on most front hubs. Constructed from 100% heat-treated chromoly, this guard is guaranteed to hold up to a long life of grinds on all surfaces! Product Specifications - Material: Heat Treated Chromoly - Axle Size: 3/8" (10mm) - Compatibility: Most Front Hubs - Weight: 2oz

A simplified quick release, utilizing an exposed/external split cam that straddles the end of the skewer. - Lighter and both easier and less expensive to manufacture, these external cam quick release levers represent an excellent value - Fits both road and mountain bike frames & forks with 100/130/135mm hub spacing - Construction: Chromoly steel skewer with alloy cam/lever and plastic/steel acorn-nut - Sold as a front & rear matching pair - Lengths: 133mm (FR) / 169mm (RR) - Weight: 58g (FR) / 64g (RR)

Replacement freehub body for all loose-ball 49N 10mm Quick-Release rear hubs. - 11sp Road compatible freehub body with supplied 1.85mm spacer for full 8/9/10/11sp road & mountain compatibility - Requires axle removal to fit - Weight: 160g

- 6061-T6 aluminum lever construction - Cr-Mo axle - Road 100mm/130mm - MTB 100mm/135mm - 110g

- CNC machined alloy locking end nut - Cr-Mo axle construction - Patented hollow hex key anti-theft security - Fits most City, MTN and Hybrid bikes (100mm/135mm) - Lightweight and compact design - 85g (Pair)

Replacement 12x100 Adapters for HEX 28 Gravel Front Hubs. Compatible with: - HEX Gravel J-Type Front Wheels Not compatible with: - HEX Straightpull or HEX J-Type 32H Front Wheels - Boost front wheels - SPIKE/OOZY/SPOON hubs - HEX 32 J-Type or 28 Straightpull Front Hubs.

Adapts HEX 28 Gravel Front Hubs to QRx100. Compatible with: - HEX Gravel J-Type Front Wheels Not compatible with: - HEX Straightpull or HEX J-Type 32H Front Wheels - Boost front wheels - SPIKE/OOZY/SPOON hubs - HEX 28 Straightpull or HEX 32 J-Type Front Hubs.

Adapts HEX 32 J-Type F15/20 Front Hubs to 12x100. Compatible with: - HEX J-Type 32H non-Boost Front Wheels Not compatible with: - HEX 28 Straightpull or HEX Gravel Front Hubs - HEX Straightpull or Gravel Front Wheels. (see HEX 28 front hub adapters) - SPIKE/OOZY/SPOON hubs

- Adapts HEX J-Type 135/142 and Gravel Rear Hubs to 12x142mm. - Adapts HEX J-Type R150/157 Rear Hubs to 12x157mm. - Also compatible as replacement adapters for HEX J-Type and Straightpull Boost R148 Rear Hubs. Compatible with: - HEX J-Type 135/142, 150/157, and Boost 148 Rear Wheels - HEX Straightpull Boost 148 Rear Wheels - HEX J-Type Gravel Rear Wheels - XD and HG Freehub Bodies Not compatible with: - SPIKE/OOZY/SPOON hubs

Replacement Alloy Axle Shaft for HEX J-Type & Gravel 135/142mm Rear Hubs. Compatible with: - HEX J-Type and Gravel 135/142 rear wheels Not compatible with: - Boost or 150/157 rear wheels - SPIKE/OOZY/SPOON hubs